- DOWNLOAD 2021 VOLVOUU PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )
$84.00Add to cart
- DOWNLOAD PACCAR Electronic Service Analyst 5.4.3.0 SW files 27.03.2021 software trucks
$60.00Add to cart
- DOWNLOAD CAT ET Electronic Technician 2018C
$46.00Add to cart
- Description
- Tags
- Reviews (0)
Description
Circuit Description
The engine aftertreatment system monitors for the presence of the aftertreatment diesel particulate filter. This diagnostic checks to make sure that the aftertreatment diesel particulate filter is present and functioning correctly.
Component Location
The aftertreatment particulate filter is located in the exhaust system and is installed by the original equipment manufacturer (OEM). Refer to the OEM service manual.
Conditions for Running the Diagnostics
This diagnostic runs when the engine is operating and exhaust flow is above a minimum level.
Conditions for Setting the Fault Codes
This diagnostic monitors the aftertreatment diesel particulate filter differential pressure sensor. When the differential pressure is below a minimum value and exhaust flow rate is above a minimum flow rate, the fault code is set.
Action Taken When the Fault Code is Active
The ECM will illuminate the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes for two consecutive trips.
Active and stationary regeneration of the diesel particulate filter will be disabled.
The EGR valve will be closed.
Engine torque will be reduced if the engine is operated for an extended period of time with this fault active.
Conditions for Clearing the Fault Code
To validate the repair using a Diagnostic Road Test, utilize a route that incorporates both stop-and-go city driving and steady state highway driving. It may be necessary to load the unit for certain diagnostics in the ECM to run.
To validate the repair using a Chassis Dynamometer Test, utilize a routine that incorporates acceleration and motoring events, steady state highway operation, and load. This will simulate normal driving and allow the diagnostics in the ECM to run.
The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp after the diagnostic runs and passes.
The ?Reset All Faults? command in INSITE? electronic service tool can be used to clear active and inactive faults.
Shop Talk
Possible causes of this fault code include:
The aftertreatment diesel particulate filter has been removed from the vehicle
The aftertreatment diesel particulate filter is cracked or broken
The aftertreatment diesel particulate filter differential tubes are installed incorrectly, broken, loose, or have been tampered with
The aftertreatment diesel particulate filter differential tubes are installed backwards.
Reference the appropriate OEM wiring diagram when troubleshooting circuits that utilize wiring supplied by the OEM.
For intermittent power supply and data link communication issues with aftertreatment components, it is highly recommended that the OEM power distribution center fuses and relays be thoroughly checked for loose, missing, or intermittent connections.
Possible Cause:
1) Aftertreatment DPF differential pressure sensor tubes failure
2) Aftertreatment DPF differential pressure sensor failure
3) ECM calibration
Related
Tags: 1993, 2010-12, 31, 4795, Aftertreatment, CM2250, Code, Conditon, Cummins, Diesel, Exists, Fault, Filter, FMI, ISX12, Missing-, Particulate, PID, SPN
Reviews
There are no reviews yet.
Be the first to review “Cummins ISX12 CM2250 (2010-12) Fault Code: 1993 PID: SPN: 4795 FMI: 31 Aftertreatment Diesel Particulate Filter Missing- Conditon Exists”
Categories Cumminz, DTC TRUCKS, ISX12 CM2250 (2010-12)Tags 1993, 2010-12, 31, 4795, Aftertreatment, CM2250, Code, Conditon, Cummins, Diesel, Exists, Fault, Filter, FMI, ISX12, Missing-, Particulate, PID, SPN
- See AlsoCummins ISX15 CM2250 (2010-12) Fault Code: 1993 PID: SPN: 4795 FMI: 31 Aftertreatment Diesel Particulate Filter Missing- Conditon Exists - dtctruckCummins ISX15 CM2250 (2010-12) Fault Code: 3151 PID: SPN: 4794 FMI: 31 Aftertreatment 1 SCR Catalyst System Missing- Condition Exists - EcuForce TruckWhat Is Fault Code SPN 5397 FMI 31? (Cummins, Freightliner)
$56.00Add to cart
- DOWNLOAD Detroit BackDoor Password Generator V1 V2
$35.00Add to cart
- DOWNLOAD JPRO 2022 V3 software professional download ( JPRO 2022 V3 ) 1 PC
$88.00Add to cart
- Related Products
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
JPRO
DOWNLOAD Noregon JPRO Commercial Fleet Diagnostics 2017 v3 (Copy)$40.00Add to cart
cummisznn
Cumminmms Insite pro 8.9 Diagnostic Software$80.00Add to cart
Trucks software
JPRO Diagnostic Software Download 2024$100.00Add to cart
Trucks software
AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125$120.00Add to cart
Trucks software
DOOSAN diagnostic software DMS-5 3.1.3 [2023.11] 1PC$106.00Add to cart
Trucks software
Bendix Acom Pro 2023 V1 diagnostic software 1PC$83.00Add to cart
Trucks software
VOLVOUU PTT TECH TOOL 2.8.220 2023 Last version 1pc$200.00Add to cart
Trucks software
Download Allison Doc Premium Update 2023 v2$105.00Add to cart
Trucks software
DOWNLOAD VOLVOUU PREMIUM TECH TOOL PTT 2.7.30 Developer + Devtool + INSTALATION VIDEO!$60.00Add to cart
BOBCAT
SERVICE MANUAL BOBCAT 853 sms$45.00Add to cart
JPRO
$85.00Add to cart
Trucks software
Diagnostic Software for Navistar Diamond Logic Builder 2023 (DLB)$94.00Add to cart
INTERNATIONAL ENGINES
$45.00Add to cart
DETROIT
SERVICE MANUAL DETROIT DIESEL DD15 , DD13 Service Workshop Repair Manual$45.00Add to cart
Trucks software
DOWNLOAD Wabco PIN Code Calculator Diagnostic Software PIN 1 PIN 2$15.00Add to cart
JPRO
DOWNLOAD JPRO 2022 v3 ( 1 PC )$93.00Add to cart